|
WELCOME TO THE CLEANING GUIDE. THIS PAGE WILL
HELP YOU UNDERSTAND HOW TO CARE FOR YOUR
TRUFILTER AND HOW TO USE THE FEATURES OF YOUR
FILTER TO SEE IF YOUR ENGINE IS HEADED FOR A
BREAKDOWN! OUTLINED BELOW IS A STEP BY STEP GUIDE
 YOUR TRUFILTER IS DESIGED AS A SPIN APART PRODUCT, YOU CAN
EITHER REMOVE THE OUTER CUP OR REMOVE THE ENTIRE FILTER,
THIS IS YOUR CHOICE
|
 GRASP THE OUTER CUP WITH THE FINGER HOLDS AND TURN THE
CUP COUNTER CLOCKWISE TO REMOVE THE OUTER CUP. IF YOU
WANT TO REMOVE THE ENTIRE FILTER TURN THE OUTER CUP A
HALF TURN TO TIGHTEN THE OUTERCUP TO THE HEAD UNIT.
THEN SPIN OFF THE ENTIRE FILTER
|
 REMOVE THE OUTER CUP AND EXPOSE THE FILTER ELEMENT
|
 NOW THAT THE ELEMENT IS EXPOSED SNAP THE ELEMENT
OFF THE HEAD UNIT AND LEAVING THE HEAD UNIT ON
THE BLOCK, IF YOU WANT THE ENTIRE FILTER REMOVED
SIMPLY SPIN OFF THE ENTIRE FILTER AND FOLLOW THE
SAME STEPS
|
 THIS IS HOW YOUR UNIT SHOULD LOOK IF YOU ARE FOLLOWING THE STEPS
|
|
 TAKE THE FILTER ELEMENT TO YOUR PREPARED CLEANING AREA.
USING YOUR THUMB OR A SOFT OBJECT (A HAMMER HANDLE) SNAP
OUT THE BASE PLUG. YOU CAN USE ANY PRODUCT THAT YOU
WISH TO CLEAN YOUR TRUFILTER. CHOOSE A SOLVENT CLEANER
THAT BREAKS UP OIL, LIKE BRAKE CLEANER. YOUR TRUFILTER
WILL NOT BE HARMED BY ANY SOLVENTS OR CLEANERS
|
 LOCATE THE MAGNET ON THE BOTTOM OF THE BASE PLUG.
INSPECT THE MAGNET FOR DEBRIS. THIS MAGENT IS A
EARLY WARNING DEVICE THAT WILL TRAP ROD AND BEARING
MATERAIL. IF YOU HAVE A LARGE BUILD UP OF METAL, TAKE
THE BASE PLUG TO YOUR MECHANIC. CLEAN THE MAGNET
AND BASE WITH YOUR CLEANER REMOVING ANY DEBRIS
|
 AFTER INSPECTING YOU FILTER MEDIA FOR DEBRIS, TAKE
YOU CLEANER AND SPRAY FROM THEINSIDE OF THE FILTER
MEDIA OUTWARD TO REMOVE DEBRIS FROM THE MEDIA.
WE AT TRUFILTER SUGGEST A SPRAY CLEANER THAT INCLUDES
THE RED TUBE FOR DIRECT CLEANING.
|
 USE THE SAME CLEANER TO WASH OFF THE BASE PLUG
AND MAGNET
|
|
|
 IF YOU HAVE ACCES TO AIR, A LITTLE SQUIRT OF AIR
FROM THE INSIDE BLOWING OUTWARD IS A GREAT
WAY TO INSURE ALL DEBRISIS REMOVED FROM THE
FILTER MEDIA
|
|
 YOU CAN EITHER WIPE YOUR FILTER MEDIA AND BASE
PLUG WITH A CLEAN RAG OR LET STAND TO DRY. EITHER
WAY IS FINE. ONCE DRY, PRESS THE BASE PLUG BACK
INTO THE FILTER MEDIA
|
|
 RETURN BACK TO YOUR VEHICLE AND SNAP THE FILTER
MEDIA BACK ONTO THE HEAD UNIT, MAKE SURE THAT
YOU COMPLETELY SNAP THE FILTER MEDIA ONTO THE
HEAD UNIT
|
 BEFORE REPLACING THE OUTER CUP, INSPECT INSIDE THE CUP
FOR ANY DEBRIS, USE A CLEAN RAG AND YOUR CLEANER AND
RINSE OUT THE CUP. DRY THE CUP WITH A RAG.
|
 REPLACE THE OUTER CUP OVER THE FILTER MEDIA AND
SCREW THE CUP ONTO THE HEAD UNIT. THE THREADS
SHOULD BE SMOOTH. YOU WILL FEEL THE CUP TIGHTEN
AGAINST THE TOP O-RING. HAND TIGHTEN ONLY. |
 INSPECT FOR ANY LEAKS, AND YOU ARE READY TO GET ROLLING. |
|
ONE OF THE TRUFILTER BENEFITS IS THAT OUR SYSTEMS IS DESIGNED FOR 100% FILTRATION. AS YOU REACH A POINT WHERE YOU WOULD NORMALLY CHANGE YOUR OIL, SIMPLE REMOVE THE OUTER CUP AND FILTER MEDIA FROM YOUR FILTER, INSPECT FOR DEBRIS AND CHECK THE STATUS OF YOUR OIL. IF EVERYTHING IS CLEAN AND YOU HAVE NO DEBRIS AND THE OIL LOOKS AND SMELLS GOOD, THEN YOU HAVE NO REASON TO CHANGE YOUR OIL. WHY CHANGE CLEAN OIL. THIS IS ONE OF THE GREAT BENEFITS OF A TRUFILTER. WE GIVE YOU THE CONTROL TO MANAGE YOUR OIL, INSPECT FOR A POSSIBLE ENGINE FAILURE AND KEEP YOU ENGINE LASTING LONGER WHILE PROTECTING THE ENVIRONMENT. LESS OIL CHANGES ALSO SAVES YOU MONEY. WITH TRUFILTER YOU WILL EXTEND THE LIFE OF YOUR ENGINE THROUGH OUR SEPERIOR TECNOLOGY OF FILTERING OIL!
WE HOPE YOU ENJOY YOUR TRUFILTER |
| |
| |
877-290-1318 - www.trufilter.com |
|
|
